The muddy water test equipment mainly used to simulate and monitor work performance of the automobile motors, car headlights frequently or intermittent work with muddy water conditions. Muddy water test chamber from Wewon Environmental Chambers Co., Ltd. include the testing room, muddy water recycle system, muddy water churn-dasher, air flow system, control system and refrigeration system. The compressor for refrigeration system we choose France Tecumseh hermetically sealed compressor with 10 years good quality guarantee !
We have the mud water testing machine quality check equipment, mechanical shaking table and environmental testing instrumentality and dong the testing service for the components/ spare components that returning into Wewon workshop.
During the production process for muddy water test equipment, for each process will do self-test, mutual inspection and get approve by the quality check department and going to the next process｜Wewon Environmental Chambers Co., Ltd. Copyrights
Test Room Dimension
≤75db is measured 1 meter away from the machine in front of the machine and 1.2 meters away from the ground
40A, AC 380V, 50Hz
The ambient temperature is +25 ℃, the relative humidity is ≤ 85% R. H, and the value measured under the condition of no sample in the muddy water test chamber.
Conditions of Use
3 PCS Nozzles include, Spacing 300mm
The nozzle transversely sprays the sample
Between 0℃~ 4 ℃, (refrigeration compressor + mixing pump)
The case of the test chamber is of overall structure, and the mud saline water tank and the high-pressure pumping system are located on the bottom of the chamber.
The control system is on the right of the test chamber.
The muddy water test chamber is of single door, which is sealed by organic glass and double-layer anti-ageing silicone rubber.
The muddy water test chamber has inspection window and windscreen wiper.
An illuminating lamp that can be controlled by the switch is installed on the equipment.
The inner case is lined up on the left side and sprayed directly on the sample.
Use 3% Arizona powder for muddy water
Use channel steel welding test department at the bottom of the mesh structure, on the surface of steel plate for motor installation,
Test Sample Fixation
Laid muddy water shower test equipment opening strengthening treatment for installation of the sample on the right side of the fixed frame, test indoor connection to support the bottom of the channel steel welded with base｜Wewon Environmental Chambers Co., Ltd. Copyrights
Laid above 1.2 mm thick steel plate to strengthen for installation of the generator, the plates welded to the outside of the test in the gallbladder wall.
Material of inner test room: SUS316# stainless steel 1.2 mm thick.
Conditions of Use
Material of exterior structure: The housing is made of cold-rolled steel plate with plastic spraying｜SUS304# stainless steel 1.0 mm thick.
The control box and test box are integrated.
Recovery of spray water at the bottom of the test room.
The spray pendulum pipe is located in the middle of the test chamber and is fixed in a unilateral way.
400*600*300mm space is reserved in the control test room for customers to install electrical accessories
Located on the door, 600X600 mm in size
Control man-machine interface, power switch, lighting switch, reserve 7″ man-machine interface｜Wewon Environmental Chambers Co., Ltd. Copyrights
Main power circuit breaker, man-machine interface controller, switchboard, cooling fan, over-temperature protector, water pump.
Distribution Control Cabinet
The bottom is recycled to save water
The Return Water System
SUS316# stainless steel is adopted to make the mud water supply tank, which is combined with the mud water anti-crystallization mixing device, the mud water supply pump and the pressure regulating device of the water supply pipe to ensure the constant pressure and constant current supply of sprinkler
Mud Water Supply System
Manual water replenishment method is adopted, and the prepared mud water can be directly imported into the mud water tank
In order to prevent the blockage caused by soil crystallization in the pipeline, the clean water supply will be automatically started after the test, and the soil in the pipeline will be cleaned
Pipeline Cleaning System
Directly connected to the water pipe, the required water supply pressure ≧ 2kgf / cm2
Safety Device for Muddy Water Test Equipment｜Overload, short circuit protection
The Spray Pump
Leakage protection, overload and short circuit protection
The Power Supply
Overload, short circuit protection｜Wewon Environmental Chambers Co., Ltd. Copyrights
Equipment environment temperature should be kept within 0 ℃ ~ + 35 ℃
The left and right side wall plates of the muddy water test chamber shall not be less than 800 mm away from the wall, and the front wall shall not be less than 1000 mm away from the wall. When the equipment is transported, please enter the entrance or the passage, the elevator, etc., to see if they can be entered, so as not to affect the progress of your company’s project.
Installation Site Requirements
The muddy-water shower test chamber is used to simulate devices that frequently or occasionally work under muddy environment such as automobile motor, to evaluate the work performance of the equipment. ｜Wewon Environmental Chambers Co., Ltd.
Before the muddy water test chamber leave Wewon workshop, Muddy water chamber will be checked by the intelligent temperature and humidity logging device (D64-2 type) and with a special high-precision test platinum resistance with a strictly quality inspection as well.
In order to further improve the company’s product and company management level, to provide users with high brand, high quality, high efficiency, world-class high-service environmental testing equipment, Wewon strictly in accordance with IS09001: 2015 version of the standard quality assurance system operation.
AC 380V Three-phase R, N + Protective grounding｜The allowable voltage fluctuation range is 10%V.
The allowable frequency fluctuation range for muddy water test chamber is 50±0.5Hz, TN-S mode power supply or TT mode power supply protection grounding resistance is less than 4Ω
The user is required to configure the air or power switch of the corresponding capacity for the muddy water test chamber at the installation site, and the switch must be independently controlled. When the equipment is used to place the power sample in the box, the sample power supply should use the external power supply, and the power supply of the machine should not be used directly.
This test is applicable to test the performance index and quality management of the product under the conditions of heavy rain, wind-blown rain, sprinkler system, wheel splash, flush or violent sea wave, which may be subjected to different ambient temperatures during the transportation, storage or use of the product.
Flammable, explosive and volatile materials are prohibited to be tested in this muddy-water shower test chamber. Test for the storage of corrosive substances, biological samples, and strong electromagnetic emission source samples
Spare Parts Name
SUS 304, Thickness 1.2mm
Circulating Water Pump
Ling Xiao Pump Industry
Taiwan Yu Tian
Thermal Overload Relay
Self – locking Switch with Lamp
Domestic High Quality
Domestic High Quality
There has another muddy water test solution which based on highly temperature test. Hot wind temperature range: RT +10℃ ~ +200℃, The main system include test room, muddy water recycle system, muddy water stir unit, Hot air dryer, rotation table and control system with 7″ programmable touch screen.
Testing Room Dimension
Muddy Water Spray ー Recycle Mode
Hot Air Temperature
Muddy Water Spray
Mud Water Concentration
Arizona A2 powder 5%
The nozzle of the device has self-cleaning function to prevent blocking.