According to environmental simulation tests on the physical and molecular structure characteristics of products, Through testing to determine whether the performance of the product meets the requirements. Nylon moisture absorption machine is widely used in medical, aviation, electrical equipment, mechanical equipment, shipbuilding, automobile manufacturing, household appliances, digital products, textile equipment, daily necessities, construction equipment, toys and other fields
● | Test Room 1 | 1500×1400×1700mm W×D×H 3.6 m3 | |
● | Test Room 2 | 2000×1700×2000 mm W×D×H 6.8 m3 | |
● | Test Room 3 | 1800×2200×2000 mm W×D×H 8 m3 | |
● | Test Room 4 | 2500×2000×2000 mm W×D×H 10 m3 | |
● | Test Room 5 | 3000×2500×2000 mm W×D×H 15 m3 | |
● | Test Room 6 | 3100×3100×2100 mm W×D×H 20 m3 | |
● | Temperature Range | 60℃~+85℃ (Set Value Control)|Temperature Fluctuation:±1℃ | |
● | Humidity Range | 75~98%R.H (Can Be Set To Constant Humidity) | |
● | Humidity Deviation | ±3%R.H (Humidity≥75%R.H) | |
● | Power Supply | 380V, 50Hz Three-Phase Five-Wire System |
Nylon is a material that is easy to absorb moisture. The toughness of fully hygroscopic nylon is about 8 times higher than that of dry nylon. Nylon can also increase its toughness to 1.5 to 2 times when it fully absorbs in the normal air environment, but it takes a long time to absorb moisture in the natural environment. In terms of nylon molecular structure, nylon molecules are water-absorbing molecules. Once saturated with water, the toughness of the material can be enhanced. The PA6 PA66 PA66/6 series has a higher water absorption rate.
The greater the proportion of amide groups, the greater the water absorption rate, and the product must be subjected to moisture absorption treatment after molding, so as to improve the reinforcement and toughness of the plastic parts of the product, and improve the mechanical properties. Wewon’s nylon products moisture absorption equipment is an environmentally friendly, energy-saving and high-efficiency equipment, which can accelerate the improvement of the moisture absorption efficiency of products in a short time.
The greater the proportion of amide groups, the greater the water absorption rate, and the product must be subjected to moisture absorption treatment after molding, so as to improve the reinforcement and toughness of the plastic parts of the product, and improve the mechanical properties. Wewon’s nylon products moisture absorption equipment is an environmentally friendly, energy-saving and high-efficiency equipment, which can accelerate the improvement of the moisture absorption efficiency of products in a short time.
● | The structure of the nylon moisture absorption machine’s body adopts a combined library board structure, which can be easily assembled and moved at the buyer’s site. | Equipment Structure |
● | The outer shell of the Wewon’s nylon moisture absorption machine is made of salt flower board, the surface is electrostatically painted, and the color is light gray white. The inner cavity is SUS1.0mm304 stainless steel wire drawing board, and the intermediate insulation is 100mm environmental protection high temperature resistant flame retardant foam. | |
● | The floor of the workshop is SUS3.0mm 304 non-slip patterned stainless steel plate, and the anti-slip slope ensures that the car can easily enter and leave the workshop. | |
● | According to the size of the laboratory, it can adopt a single door or double door structure, equipped with a handle; Install moisture-proof lighting on the top of the workshop (high temperature resistance, explosion-proof, moisture-proof) | |
● | The overall structure of the laboratory should be reasonably designed, beautiful inside and outside, and free of defects such as bumps and scratches. | |
● | Air control method: forced circulation ventilation, balanced temperature and humidity regulation (BTHC), the control system controls the output of the heater according to the set temperature point through the PID automatic calculation output result, and finally achieves a dynamic balance. | |
● | Air circulation device: built-in circulating air duct and centrifugal fan, for effective heat exchange, to achieve the purpose of temperature and humidity changes. | |
● | Electric steam humidifier;Air heating method: high-quality nickel-chromium alloy electric heater, non-contact control method;Adopt upper and lower inlet circulation air duct (304 stainless steel) |
Wewon’s nylon products moisture absorption equipment has changed the traditional boiling method and the pollution to the environment, Modification of nylon, strengthening and toughening without watermark, reducing enterprise cost, fast and stable moisture absorption. The main component of nylon material is polyamide, and the amide group (NHCO) is that nylon has both water absorption and dehydration double-sided properties. Nylon material without water absorption has strong brittleness. It is easy to break during the assembly process and cause unnecessary losses, but after saturated water absorption, the toughness of the material can be increased, and the dimensional stability can be improved at the same time.
Nylon products are generally placed in the natural environment (temperature 23°C, humidity 50%RH), and it takes 1 to 3 months for natural moisture absorption, but the use of Wewon’s nylon products with constant temperature and humidity water treatment can compress the moisture absorption time to within a few hours , so that nylon materials (PA6/PA66 and modified materials) can quickly reach a saturated moisture absorption state, and the materials treated by Wewon’s nylon products with constant temperature and humidity water treatment can be used directly without drying, wiping and blowing.

Nylon products are generally placed in the natural environment (temperature 23°C, humidity 50%RH), and it takes 1 to 3 months for natural moisture absorption, but the use of Wewon’s nylon products with constant temperature and humidity water treatment can compress the moisture absorption time to within a few hours , so that nylon materials (PA6/PA66 and modified materials) can quickly reach a saturated moisture absorption state, and the materials treated by Wewon’s nylon products with constant temperature and humidity water treatment can be used directly without drying, wiping and blowing.
● | Equipment Parts Name | Model Specifications | REMARK |
● | Library And Studio Materials | Anti-Corrosion Salt Pattern | Wewon Tech |
● | Bottom Frame | Channel 8 | Bao Steel |
● | Touch Screen | U 660 | Excellent |
● | Heating Pipe | 220V304 Stainless Steel | Sub Peak |
● | Humidification Tube | 220V316L Stainless Steel | Sub Peak |
● | Temperature And Humidity Sensor | PT100 | WELL |
● | Thermal Control | 0-320 degrees 3PIN | Germany |
● | Air Circulation System | 304 Stainless Steel | Wewon Tech |
● | Cyclic Long Axis Motor | 750W Stainless Steel | Yizheng |
● | Circulating Centrifugal Fan | 304 Stainless Steel | Yizheng |
● | Air Circuit Breaker | C65N-C6-40A | Schneider |
● | AC Contactor | LC1 series | Schneider |
● | Solid State Relay | TSR series | Kang Yu |
● | Intermediate Relay | RXM series | Schneider |
● | Time Relay | REXL | Schneider |
● | Three-Color Alarm | TB50-3W-D-J | Taiwan |
● | Switching Power Supply | AC/DC24V | Mean Well |
● | Electric Wire | BRR450-1.5/4 | Wuxi Pearl |
● | Water Level Switch | SW-12-NO | Western |
Since the characteristics of nylon injection molding products are water absorption, it is necessary to carry out humidity conditioning treatment for nylon products. Especially for the auto parts industry that uses a lot of nylon raw materials, the humidity control equipment directly affects the production. The nylon moisture absorption test equipment designed and produced by Wewon Tech provides professional services to users. If you are looking for equipment for dehumidification of nylon materials, Please contact our technical staff. Thank you.