Short Circuit Test Chamber for Lithium Ion Battery Short Circuit Test Machine

The short circuit test chamber is used to test whether the lithium ion battery will explode and catch fire under the condition of a certain resistance short connection, and show the maximum current of the short connection through the relevant instrument. The short circuit test chamber integrated a variety of battery short circuit test standard requirement. According to the requirements of standard short circuit device must conform to the scope of internal resistance ≤5mΩ thus to get the large short-circuit current test requirements.

How to Use the Short Circuit Test Chamber ? After the battery is fully charged according to the prescribed test method, it is placed in an environment of 55℃ ±5℃. After the battery temperature reaches 55℃ ±5℃, it is placed for 30 minutes. Then use wire connection battery positive and negative port, and ensure that all external resistance is 80mΩ ±20mΩ

During the test with short circuit test chamber, the temperature change of the battery is monitored. When one of the following two situations occurs, the test is terminated. (1) Battery temperature drops to 20% below peak. (2) The short connection time reaches 24 hours. Test results judgement: the battery should not fire or explode, and the highest temperature should not exceed 150℃

Short Circuit Test Chamber

Product ModelWEW-SCTC-1000A
Testing Room500x500x500 mm
Test StandardUN 38.3, UL 2054
Measurable Battery 0~100V
DC Response Time≤5 μs
Large Short Circuit1000A
Internal Resistance≤5 mΩ
Temperature Accuracy0.1℃
Temp Uniformity±1℃︱Short Circuit Test Chamber
Temperature Control+10℃~+200℃
Mechanical Life300000 Times
Working VoltageAC 230V, 50 Hz, 60 Hz
Impulse VoltageAC 1kv/ 1.2- 50μs (peak) 1 min

In addition, in the circuit design of the short circuit devices are also required to withstand the impact of high current, so we choose the industrial-grade dc electromagnetic contactor and copper wiring terminal and internal copper diversion, generous copper effectively increase the cooling effect, make large current short circuit device safer, effectively reduce the wastage of the testing equipment, to ensure the accuracy of the test data.

1.2mm thick stainless steel plate and affixed with teflon, strong corrosion resistance and flame retardant performanceInner Material
1.5 mm thick A3 cold plate baking paint treatment|short circuit test chamber for lithium ion battery short circuit test machineExternal Material
250×250 mm two-layer vacuum tempered glass observation windowSight Window
The rear of the box is equipped with an exhaust fan and a reserved exhaust pipe interface with a diameter of 100 mmAir Outlet
Open the threshold switch of power off to ensure no misoperation and ensure the safety of personnelDoor Switch
There are two test holes with a diameter of 50 mm on the left side of the machine, which are convenient to put in various temperature, voltage and current acquisition linesTesting Hole
Independently developed the force control system OYO-9206 systemController
There are four universal casters under the device, which can move freelyWheels


Short Circuit Test Chamber for Lithium Ion Battery Short Circuit Test Machine


This battery external short circuit test is dangerous. Please use a separate testing room and open an observation window in the testing room to record the voltage and current data when the battery is short-circuited. If you are looking for the battery crush tester for lithium battery performance testing, please visit the related lithium battery crush testing page.

related page logoBattery Crush Tester – Lithium Battery Crush Testing – Battery Safety Testing
related page logoNail Penetration Test Chamber for Lithium Ion Battery, Lithium Batteries
related page logoShort Circuit Testing Chamber for Lithium Ion Battery Short Circuit Test Machine
related page logoNail Penetration Tester For Battery Nail Penetration And Safety Testing
related page logoBattery Vacuum Dry Chamber︱High Altitude Low Pressure Chamber

1.1 The working voltage of DC is up to 660V︱Short circuit test system equip with high-current DC contactor1. DC Contactor
1.2 Rated working current 1000A (or 2000A) dc, equipped with series magnetic blowing mediastinal ceramic arc extinguishing cover arc extinguishing system
1.3 The overall structure of plane layout, the electromagnetic system and the main contact arc extinguishing system are respectively fixed on the installation base frame. The patching electromagnetic system with angular rotation and double winding suction coil are adopted, and the pressure edge device is added on the rotating angular rotation.
1.4 The main contact is made of red copper. Low contact resistance and fast reaction speed;
1.5 Contactor action reliable, safe, long life, easy maintenance.
2.1 Long Distance Wireless Control2. Remote Control
2.2 Reliable, stable, with self-locking and mutual locking function, strong anti-interference ability, long life
3.1 Measuring Voltage: 0-100v, ensuring test accuracy3. Voltmeter
3.2 Display Accuracy: F.S ±0.2% RDG ±1digit
3.3 Action Mode: Double integral mode
4.1 Measuring Current: 0-2000a and 0-1000a DC︱short circuit test chamber4. Ammeter
4.2 Display Accuracy: F.S ±0.2% RDG ±1digit
4.3 Action Mode: Double integral mode︱Short circuit test chamber for Rechargeable battery
5.1 The battery short circuit tester consists of high current short circuit contactor, remote controller, voltmeter, ammeter, etc5. Basic Configuration
5.2 Necessary Accessories: 1000A test copper cable, etc

© Copyright 2014-2018. Wewon Environmental Chambers Co., Ltd.